Proceed DAP (non-CE) Uživatelský manuál

DAPDigital AudioProcessorOwner’s ManualRPR O C E E D

10Finally, an infrared receiver and transmitter for remote control of the DAP ispositioned on the left side of the main display. Owners of learning re

116 POLARITYThe DAP is a non-inverting device—that is, digital inputs which indicate apositive voltage generate a positive analog output. Some recordi

12PR O C E E DRd a p by MADRIGAL AUDIO LABORATORIESaes/ebuanalog outputs~ ac mainsmains fuse:.5A (250V) slo-blo 5x20mmplease see bottom panel for vol

13123Pin 1: Signal groundPin 2: Signal + (non-inverting)Pin 3: Signal – (inverting)Connector ground lug: chassis groundRefer to your preamplifier’s op

144 AES/EBU DIGITAL INPUTThis input accepts digital audio conforming to the 110Ω AES/EBU digitalinterface standard (via a cable equipped with XLR-type

158 ST DIGITAL INPUTThis input accepts digital audio conforming to the ST optical (sometimescalled “AT&T”—ST is a trademark of AT&T and the co

16Caution! The Proceed DAP has been safety-tested and is designedfor operation with a three-conductor power cord. Do notdefeat the “third pin” or eart

17Using the DAPInput Selection The DAP has five digital inputs. Using the up/down buttons, you may scrollthrough the five inputs in either direction.

18Remote Control of the DAPThe DAP includes both an infrared receiver and an infrared transmitter. With thiscapability, it can “teach” a learning remo

19(If you are uncertain as to how to prepare your remote control for learningnew commands, refer to the instructions provided with the remote control.

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DONOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.REFER SE

20The DAP will display a “L 00” code when it has entered its teaching modeand is ready to help the remote control learn the commands that corre-spond

21(If you are uncertain as to how to prepare your remote control for learningnew commands, refer to the instructions provided with the remote control.

22Care & MaintenanceTo remove dust from the cabinet of the DAP, use a feather duster. To remove dirtand fingerprints, we recommend isopropyl alcoh

23U.S. and Canadian Warranty90-Day Limited Warranty This Proceed® product is warranted to be free from defects in material and work-manship under norm

24Obtaining ServiceWe take great pride in our dealers. Experience, dedication, and integrity makethese professionals ideally suited to assist with our

25SpecificationsThe correlation between published specifications and performance is unreliable. Alist of numbers reveals virtually nothing. All techni

26Dimensions12.27"31.2cm0.98"2.49cm13.25"33.7cm13.25"3.5"8.9cm13.25"33.7cmPR O C E E Dd a pstandbymute17.25"43.8cm1

27

630408 © 12/1999 Madrigal Audio Laboratories, Inc. All rights reserved. Printed in U.S.A.RPR O C E E Dis a registered trademark of Madrigal Audio Labo

Important Safety InstructionsPlease read all instructions and precautions carefully and completely before operating your DAP digital audioprocessor.1.

4From all of us at Madrigal Audio Laboratories, thank you for choosing theProceed DAP digital audio processor.A great deal of effort went into the des

5Table of ContentsUnpacking and Placement ... 6Unpacking ...

6Unpacking and PlacementUnpacking Unpack your Proceed® DAP digital audio processor and keep all packing mate-rials for future transport. Locate and re

7Operating VoltageThe DAP digital audio processor is set at the factory (internally) for 100V, 120V,200V, 220V, or 240V AC mains operation as appropri

8Special Design FeaturesCongratulations on your purchase of the Proceed DAP. The Madrigal design teamis confident you will enjoy the outstanding perfo

9PR O C E E Ddappowermutemodepolarity2 3 4 561Front Panel1 STANDBY & STANDBY LEDAssuming that the DAP’s power cord is connected to AC power, press